Ordering details | |
|---|---|
| Product type description | TV8S 355-12Z - Ordering suffix |
| Article number | 101179254 |
| EAN Code | 4030661311722 |
| eCl@ss | 27-27-26-01 |
Approval | |
| Approval |  BG USA/CAN CCC |
Classification | |
| Standards | EN ISO 13849-1 |
| B10d Normally-closed contact (NC) | 20.000.000 |
| Mission time | 20 Years |
| notice |  |
Global Properties | |
| Permanent light | TV.S 355 |
| Standards | EN 60947-5-1, BG-GS-ET-15 |
Compliance with the Directives (Y/N)  | Yes |
| Materials | |
| - Material of the housings | Aluminium |
| - Material of the contacts | Silver |
| Housing coating | painted |
| Weight | 323 |
Mechanical data | |
| Design of electrical connection | Screw connection |
| Cable entry M 20 x 1.5 | 3 |
| Cable section | |
| - Min. Cable section | 0,75 |
| - Max. Cable section | 2.5 |
| Design of actuating element | Other |
| Mechanical life | > 1.000.000 operations |
| Switching frequency | max. 1000 /h |
| notice | All indications about the cable section are including the conductor ferrules. |
| Shaft bore | Ø 8 |
| Positive break angle | 7 ° |
| Positive break torque | 60 Ncm |
Ambient conditions | |
| Ambient temperature | |
| - Min. environmental temperature | −25 °C |
| - Max. environmental temperature | +70 °C |
| Protection class | IP67 |
Electrical data | |
| Design of control element | Normally open contact (NO), Opener (NC) |
| Switching principle | Creep circuit element |
| Number of auxiliary contacts | 1 |
| Number of safety contacts | 2 |
| Rated impulse withstand voltage Uimp | 4 kV |
| Rated insulation voltage Ui | 250 V |
| Thermal test current Ithe | 10 A |
| Utilisation category | AC-15: 230 V / 4 A, DC-13: 24 V / 4 A |
| Max. fuse rating | 6 A gG D-fuse |
ATEX | |
| Explosion protection categories for gases | None |
| Explosion protected category for dusts | None |
Dimensions | |
| Dimensions of the sensor | |
| - Width of sensor | 66.7 mm |
| - Height of sensor | 107 mm |
| - Length of sensor | 65.3 mm |
notice | |
| Setting assistance | Grub screw for location, shaft pre-drilled for pin |
| Universal joint available to compensate for axial displacement (only for shaft bore 10 mm) | |
| By turning the head in 90° steps, 8 actuating planes are possible. A Torx T10 screwdriver is needed for this purpose. Even when the screw is removed, the head is self-retaining. The switch can still not be tampered. | |
Diagram | |
 Note Diagram  positive break NC contact active no active Normally-open contact Normally-closed contact | |
Switch travel diagram | |
 Notes Switch travel diagram  Contact closed Contact open Setting range Break point Positive opening sequence/- angleVSadjustable range of NO contact VÖadjustable range of NC contact Nafter travel | |
| ...-NPT | Cable entry NPT 1/2“ |
Ordering details
По вопросу интересующей Вас продукции, пожалуйста, свяжитесь с нами:
8 (029) 555-8-000 | |
8 (044) 555-8-000 | |
8 (017) 255-8-000 |
Или отправьте нам запрос на e-mail: zapros@filfar.by
