Ordering details | |
---|---|
Product type description | BN 120-10Z/V |
Article number | 101186841 |
EAN Code | 4030661335414 |
eCl@ss | 27-27-01-04 |
Approval | |
Approval | - |
Global Properties | |
Permanent light | BN 120 |
Standards | - |
Compliance with the Directives (Y/N) ![]() | Yes |
suitable for elevators (Y/N) | Yes |
Mounting | central with threated flange M12 x 1 |
Active principle | Magnetic drive |
Materials | |
- Material of the housings | Plastic, glass-fibre reinforced thermoplastic |
- Material of the cable mantle | LiYY |
Housing construction form | cylinder, thread |
Weight | 30 |
Recommended actuator | BP 10 S, 2 x BP 10 S, BP 15 S, BP 34 S, BP 20 S, BP 31 S, BP 11 S, 2 x BP 11 S, BP 12 S, 2 x BP 12 S, BP 21 S, 2 x BP 21 S, BP 22 S, 2 x BP 22 S, BE 20 S |
- Lift switchgear | BP 10, 2 x BP 10, BP 15, BP 34 |
Mechanical data | |
Design of electrical connection | Cable |
Cable length | 1 |
Conductors | 2 x 0,25 |
AWG-Number | 23 |
Mechanical life | 10.000.000 operations |
Electrical lifetime | 1.000.000 … 10.000.000 operations |
Actuating planes | front side |
Switch distance | 5 … 55 BP 10S = 5 mm 2 x BP 10S = 10 mm BP 15S = 6 mm BP 34S = 20 mm BP 20S = 15 mm BP 31S = 15 mm BP 11S = 5 mm 2 x BP 11S = 15 mm BP 12S = 10 mm 2 x BP 12S = 25 mm BP 21S = 30 mm 2 x BP 21S = 20 ... 55 mm BP 22S = 25 mm 2 x BP 22S = 15 ... 55 mm BE 20 S = 6 mm |
- notice | Actuating distance up to 55 mm depending on actuating magnet and version The specifications with regard to the switching distances apply to the actuation of the individually mounted devices without ferromagnetic influence. Any change of the distance, positive either negative, is possible due to ferromagnetic interference. When multiple actuating magnets are used, the mutual interference must be observed. |
Type of actuation | Magnet |
restistance to shock | 30 / 11 |
Resistance to vibration | 10 … 55 HZ, Amplitude 1 mm |
Bounce duration | 0,15 |
Latching (Y/N) | No |
bias magnet (Y/N) | Yes |
Tightening torque for nuts | 90 |
Actuating speed | 18 |
Switching point accuracy | ± 0,25 mm |
Ambient conditions | |
Ambient temperature | |
- Min. environmental temperature | −25 |
- Max. environmental temperature | +70 |
Protection class | IP67 to IEC/EN 60529 |
Electrical data | |
Design of control element | Normally open contact (NO) |
Number of shutters | 1 |
Number of openers | 0 |
Switching time - Close | 0,35 |
Switching time - Open | - |
Switch frequency | <> |
Dielectric strength | > 200 |
Switching voltage | 200 |
Switching current | 1 A |
Switching capacity | 30 / |
Outputs | |
Design of control output | Reed contakts |
LED switching conditions display | |
LED switching conditions display (Y/N) | No |
ATEX | |
Explosion protection categories for gases | None |
Explosion protected category for dusts | None |
Dimensions | |
Dimensions of the sensor | |
- Length of sensor | 71 |
- Diameter of sensor | 10.7 |
notice | |
The opening and closing functions depend on the direction of actuation, the actuating magnets and the polarity of the actuating magnets. | |
When the switches and actuators come together, the colours must coincide: Red (S) to red (S) and green (N) to green (N). This does not apply to the bistable contact. | |
The switch is to be mounted on iron with a non-magnetic layer of at least 20 mm. | |
Included in delivery | |
Actuators must be ordered separately. | |
Diagram | |
![]() Note Diagram ![]() ![]() ![]() ![]() ![]() | |
Switch travel diagram | |
![]() Notes Switch travel diagram ![]() ![]() ![]() ![]() ![]() VSadjustable range of NO contact VÖadjustable range of NC contact Nafter travel |
По вопросу интересующей Вас продукции, пожалуйста, свяжитесь с нами:
8 (029) 555-8-000 | |
8 (044) 555-8-000 | |
8 (017) 255-8-000 |
Или отправьте нам запрос на e-mail: zapros@filfar.by