Ordering details | |
|---|---|
| Product type description | AZM 170 B ST-AS RAP |
| Article number | 101210414 |
| EAN Code | 4030661390406 |
| eCl@ss | 27-27-26-03 |
Approval | |
| Approval |  AS-i TÜV USA/CAN |
Classification | |
| Standards | EN ISO 13849-1, IEC 61508 |
| PL | up c |
| Control category | 1 |
| PFH | 1.16 x 10-6 / h |
| - notice | up to max. 100.000 switching cycles/year |
| SIL | up 1 |
| Mission time | 20 Years |
| If a fault exclusion for hazardous damage of the 1-channel mechanics is authorized and an adequate protection against tampering is ensured, suitable for use up to: | |
| Standards | EN ISO 13849-1, IEC 61508 |
| PL | up d |
| Control category | 3 |
| PFH value | 1.01 x 10-7 / h |
| - notice | up to max. 100.000 switching cycles/year |
| SIL | up 2 |
| Mission time | 20 Years |
Global Properties | |
| Permanent light | AZM 170 AS |
| Standards | EN 50295, EN 60947-5-1, IEC 61508, EN ISO 13849-1 |
Compliance with the Directives (Y/N)  | Yes |
| Number of actuating directions | 2 |
| Active principle | electromechanical |
| Duty cycle ED | Magnet 100 % |
| Materials | |
| - Material of the housings | glass-fibre reinforced thermoplastic, Plastic self-extinguishing, |
| Housing coating | None |
| Weight | 310 |
| Guard locking monitored (Y/N) | No |
| Actuator monitored (Y/N) | Yes |
| Response time | <> |
Mechanical data | |
| Design of electrical connection | connector plug M12, 4-pole |
| Mechanical life | > 1.000.000 operations |
| Manual release (Y/N) | No |
| Latching force | 30 |
| Clamping force F | 1000 N |
| Max. Actuating speed | 2 |
Ambient conditions | |
| Ambient temperature | |
| - Min. environmental temperature | −25 |
| - Max. environmental temperature | +55 |
| Storage and transport temperature | |
| - Min. Storage and transport temperature | −25 |
| - Max. Storage and transport temperature | +85 |
| Relative humidity | 30 … 95 |
| - non-condensing | |
| - non-icing | |
| Protection class | IP67 to IEC/EN 60529 |
| Protection rating | II  |
| Air clearances and creepage distances To IEC/EN 60664-1 | |
| - Rated impulse withstand voltage Uimp | 0,8 kV |
| - Rated insulation voltage Ui | 32 VDC |
| - Overvoltage category | III |
| - Degree of pollution | 3 |
Electrical data | |
| Power to unlock | No |
| Power to lock | Yes |
Electrical data - AS interface | |
| AS-i Supply voltage | 26.5 … 31.6 VDC, Protection against polarity reversal |
| AS-i operating current | ≤ 50 |
| AS-i Device insulation | internally short-circuit proof |
| AS-i Specification | |
| - version | V 2.1 |
| - Profile | S-7.B.F.E |
| - IO-Code | 0x7 |
| - ID-Code | 0xB |
| - ID-Code1 | 0xF |
| - ID-Code2 | 0xE |
| AS-i Inputs | |
| - Channel 1 | Data bits DI 0/DI 1= dynamic code transmission |
| - Channel 2 | Data bits DI 2/DI 3= dynamic code transmission |
| AS-i Outputs | |
| - DO 0 | Solenoid control |
| - DO 1 | not used |
| - DO 2 | not used |
| - DO 3 | not used |
| AS-i Parameter bits | |
| - P0 | Safety guard and actuator detected |
| - P1 | Solenoid interlock locked |
| - P2 | not used |
| - P3 | not used |
| AS-i input module address | 0 |
| - Default on address 0, programmable via the AS-Interface Master or Hand-held programming device | |
Electrical data - Auxiliary voltage (Aux) | |
| Supply voltage UB | 24 VDC (−15 % / +10 %) stabilised PELV |
| Operating current | ≤ 500 |
| Device insulation | ≤ 4 A (if used in accordance with UL 508) |
LED switching conditions display | |
| LED switching conditions display (Y/N) | Yes |
| AS-i LED switching conditions display | |
| (1) green LED | Supply voltage |
| (2) red LED | Communication error / slave address = 0 |
| (3) yellow LED | Enabling status |
ATEX | |
| Explosion protection categories for gases | None |
| Explosion protected category for dusts | None |
Dimensions | |
| Dimensions of the sensor | |
| - Width of sensor | 90 |
| - Height of sensor | 75.5 |
| - Length of sensor | 30 |
Pin assignment | |
| 1 | AS-i + |
| 2 | Aux − (P) |
| 3 | AS-i − |
| 4 | Aux + (P) |
notice | |
| Interlocks with power to lock principle may only be used in special cases after a thorough evaluation of the accident risk, since the guarding device can immediately be opened on failure of the electrical power supply or when the main switch is opened. | |
Included in delivery | |
| Actuators must be ordered separately. | |
Ordering details
По вопросу интересующей Вас продукции, пожалуйста, свяжитесь с нами:
8 (029) 555-8-000 | |
8 (044) 555-8-000 | |
8 (017) 255-8-000 |
Или отправьте нам запрос на e-mail: zapros@filfar.by
